Search results

Kevin b swapped in a 3rz out of 95'? and couldn't get it wired up. He has a few threads on the swap.

Kevins nickel/jb weld egr block off job didnt last too long. Sounded like a derby car coming down the mountain last night lol. I welded it up today and grinded it flat on the belt sander so it would seal good. How to Tape inner beads on already mounted bead locked tires.

Ive been slowly tidying up things on the old runner. I ended up rerouted the clutch line and both brake lines by the caliper only to find out the brake master cylinder was leaking internally. Got a new master in it and had my lady help me bleed it. Most of you may not know that my lady is deaf...

Smoked the short shaft bouncing around the waterfalls on hanging tree the other day. After wheeling in the water with other friends that have stickies i have concluded i need stickies to be cool. I couldn't climb the last water fall in my two seater with all 73 squirrelpower singing after 15...

I just when with what psc recommends also i dont think they like warrantying a pump if your not using what they say to. I find it funny that my stock 5.3 pump lasted a good year and half with just cheap power steering fluid before it quit. I really haven't noticed much steering improvement with...

Pimped out the steering a little more the other day. I have been hearing a slight wine out of the new pump so who tf knows. I blew out all the lines trying to get the old fluid out. Installed a check valve on the steering pressure line off the pump Installed unicorn piss steering fluid, or...

Here you go bud. Rme thread thats not in Garage/Shop and tools?

Toyota based buggy built in 2012. 48" wide chassis, built with 1.5" DOM tubing, Im 6' 3" and have plenty of head room. It has a Toyota 20r 4 cylinder that has been gone through in 2010 that runs off propane, manual toyota 5 speed transmission, Dual Toyota transfer cases with 4.7 gears in the...

Got my fold down cot beds installed in my enclosed trailer. Im slowly turning it into a shitty camper that hauls both my buggys.

There was a slight mis every now and then when i was letting it get up to temp and the #1 cylinder was about 60* cooler than the rest. Getto purple ground wire for now.

As some of you may have known i bought Kevins B gray bastard 4 runner and have finally had time to tinker on it. The thread worthy news is that i got it running over the last few weeks with the help of some of my friends. I have been putting off this project for some time and have bitching to...

Tie rod and drag link appear to be backwards on the p/s knuckle.

I would if you was closer and new what you want.

Going on 8 years of grave yards here. I love it. I dont sleep much so i get alot done before my shift. 8pm-5am sun-thur. For the first 5 of those years we was 4-12s and we had to work two weeks of weekend two weeks of weekdays and switch. I dont miss the weekends but i do miss the extra days...

All that new tube work and your going to leave the factory b to b hoop. B to B hoops give me cancer. I like a the smooth transition of the A to C pillar. I dig your metal car port turned garage, brings back memory's.

Bring it to Richfield ;)

They sell decent sealed bulk head fitting you wouldnt have to weld. just drill a hole.

Fill it with water and weld it out. NBD

Weld some fittings on the side of the tank for a sight tube thats what we run on our fuel cells. Ive seen how much the plastic tubes or wiffle balls cost and have read about guys cutting up old oil quart bottles and using them instead since they are practically free.

Im sure you could plumb in a jogger valve with a return back into the reservoir. Ive always wanted to plumb in a orbital valve so i a can turn a wheel to bend and turn it back to return.