Search results

I am interested in getting a mpg readout meter for my 79 carbed chevy 350. I would like to get one that will give me a average pet tank and not just a current mpg readout like a cheezy vacuum guage with fuel numbers on it. In my searching I can only find a marina guage that is $300+ so that is...

I need a rear windshield for a 87 vw golf. LMK where you are and what you want for it.

I am looking for a shop that can tune my rebuilt stock bore chevy 350 with cam and edelbrock carb. Hoping there is a shop that can set the trans kick down cable and a/f ratio to peak preformance. Does such a shop exist and if so where and about that am I looking at spending. I want it done right...

I am in need of some fiberglass repair. It is a simple flat fender with a 90 degree bend up top that is also flat. No fancy bends to be dealt with. I have had a few bids and they are around $550-600 for the repair and paint. Wondering if anybody here can do it or if I should tackle it myself. If...

I searched and found little about a KIT. I dont want to use junkyard parts or manually control the lock-up. I am looking for a kit to lock up a 700r4 that will be able to function properly with a carbed engine. Anybody have a kit they have used or heard good things from. The kits I found...

Might be getting a 1985 k5 blazer for parts. Have a few questions about compatibility. The vehicle has 6 lug 10 bolt front and rear with limited slip. (dont know if they are factory or aftermarket, will verify they are there) Will the front 10 bolt limited slip fit into my 3/4 ton 8lug 10...

I have a set of chevy spring that like all older springs have negative arch. I could get an add a leaf but I dont want any lift. I also cant find stock height springs so I an now looking at making a hybrid pack. Has anybody made a new set of leafs for the front of their chevy using the stock...

I have a set of knuckles that need new ball joints pressed in. I have the ball joints and knuckles ready to go. Where can I get somebody to press them in and what is the running rate. Not looking for a cheap deal just great service. Located in the West jordan, kearns area.

I have a th400 in my vehicle with a np208 behind it. I want to know what the changes required will be to go to a 700r4. From what I have found it looks like the 700r4 is 1 inch shorter so I would need to possibly change the driveline length. I know the case has a different spline count so I...

I have a 79 3/4ton suburban frame and running gear. 400sb with th400 and np208. The gear ratio is the stock 4.10 with a 8 lug 44 and ff14. I have 38 swampers on it and it cruises down the freeway around 2500 rpm at 65mph. I dont have lots of throttle response but can get to 65-70 with time. I...

I want to put EFI on my vehicle. It is a 79 chevy that has a factory 400 with a edelbrock carb and intake. I want to get EFI but had problems with howell harness on a previous project. Wondering what people would do. My 400 has good power for a 79 400 and supposedly has 20k on it but...

Me, my brother in law and only our rig were at snakes. We waited in the parking lot for 1/2hr before deciding to go up. Not the smartest thing to do but we went for it. It was going to be a test run for the vehicles SAS just barely finished. We were doing great and my confidence was...

Who is up for running snakes saturday? I just got my sas done on my 4runner and want to try it out.

I have a 87 toyota 4runner that has a top shift case. I bought a 4.7 gear set in a forward shift case and put them in the topshift. My question is what is needed to get the gears working in the topshift properly? I clearanced the case for the large gear and put it all back together. It...

This should be easy and I should know it and 4 hrs research should have given the answer but I cant figure it out. Mid to late 70's model chevy 350 bored 30 over with carburetor I have 3 wires on my distributor. 2 are connected in a plastic harness type connection and I think they come...

I have a 4.3 with a 700r4 and a adapted np205 I want to go with a manual trans and need to know exactly what is involved. Looking at getting a sm465 and a matching case. I dont want to buy expensive adapters. Do the sm465 already come with the bell housing adapter to mate it to the 4.3? What...

I have a 700r4 I swapped into my crawler with a np205 and adapter. The np205 is giving me problems so I want to get a different case that will bolt up. I heed a fixed rear yoke and pass drop. What cases will directly bolt up to the 700r4?

I have a ford 9" rear from a early bronco. I am changing the drums to discs but the problem I have is the wheel studs are too short to get the rotor and wheel on. Can anybody help me with the measurements on the wheel studs. I need to get a stud that is 1/2" longer. I know it is a 1/2" thread...

Like the title says, does anybody have a holley pro-injection that is running or complete. I have a partial system that I need to find out how the wires go and the sensors needed. The harness that came with it is torn up at the fuel controller plug and the wires have terminals and eyelets on...

Wanting to paint my 4runner camo. Looking to use spray paint and wondering how it will hold up. The rig is a driveway sitter with occasional street and trail use. Read that I should use krylon spray paint and sand the body with 200-400 grit before painting. Anybody done it, or heard of it? Good...