King pin 60 high steer arms, thick aluminum 5 bolt for ried knuckles or will work with stock 4 bolt knuckles. $100
Currie hd semi float 9 inch rear housing with double drilled explorer disc brakes rotors (5 on 5 1/2) & calipers 60 inch wide wms. No third member, needs cleaned up one shaft twisted splines. $300
Disc braked Ford dana 60 rear complete with 30 spline detroit locker 4.10 gears and a thick after market diff cover. Has GM calipers with 3/4 ton rotors even has the rubber brake lines $500
low pinion driver drop front dana 60 housing from a 4x4 haliburton van with no inner c's no outers no shafts, 4.10 gears no carrier. with inner C's put on the the exhisting tubes this would make a 67 inch wide front. Thats a 3 inch wide spring perch welded next to the diff $100
1 used set of 4.88's for a low pinion dana 44 $50
ford 460 short block brand new rebuilt bored .040 over never installed or started $200
ford NP 435 4 speed from 78 ford bronco with 351M $150
ford dana 60 rear 30 spline 4.10's open complete but dissasembled $50
sm 465 4 speed 4wd trans & shifter $50
scout close ratio t-19/d 20 $50
suzuki samurai axles pair stock $250
suzuki samurai t-case all stock $150
suzuki samurai 5 speeds X2 $50 each
used dana 44 30 spline spool $100
front pass side drop d44 61 wms with 6 lug full size outers flat tops milled and drilled for high steer custom diff offset for samurai or CJ not finished no gears or carrier $100
rear pass side drop d44 housing & shafts 6 lug with disc brake brackets and calipers no gears or carrier $50
small block ford ZF 5 speed, rebuilt from a trans shop in junction with maybe 500 miles on it $300
I also have miscelanious steering boxes drive shafts wheels early CJ parts samurai parts, a whole 1987 ford f-150 302 5 speed 4x4 parts truck. All located in Fruita/ Grand Junction all pickup only. Thanks for looking. PM is the best way to reach me. Make offers, just want to clean up my life!
Currie hd semi float 9 inch rear housing with double drilled explorer disc brakes rotors (5 on 5 1/2) & calipers 60 inch wide wms. No third member, needs cleaned up one shaft twisted splines. $300
Disc braked Ford dana 60 rear complete with 30 spline detroit locker 4.10 gears and a thick after market diff cover. Has GM calipers with 3/4 ton rotors even has the rubber brake lines $500
low pinion driver drop front dana 60 housing from a 4x4 haliburton van with no inner c's no outers no shafts, 4.10 gears no carrier. with inner C's put on the the exhisting tubes this would make a 67 inch wide front. Thats a 3 inch wide spring perch welded next to the diff $100
1 used set of 4.88's for a low pinion dana 44 $50
ford 460 short block brand new rebuilt bored .040 over never installed or started $200
ford NP 435 4 speed from 78 ford bronco with 351M $150
ford dana 60 rear 30 spline 4.10's open complete but dissasembled $50
sm 465 4 speed 4wd trans & shifter $50
scout close ratio t-19/d 20 $50
suzuki samurai axles pair stock $250
suzuki samurai t-case all stock $150
suzuki samurai 5 speeds X2 $50 each
used dana 44 30 spline spool $100
front pass side drop d44 61 wms with 6 lug full size outers flat tops milled and drilled for high steer custom diff offset for samurai or CJ not finished no gears or carrier $100
rear pass side drop d44 housing & shafts 6 lug with disc brake brackets and calipers no gears or carrier $50
small block ford ZF 5 speed, rebuilt from a trans shop in junction with maybe 500 miles on it $300
I also have miscelanious steering boxes drive shafts wheels early CJ parts samurai parts, a whole 1987 ford f-150 302 5 speed 4x4 parts truck. All located in Fruita/ Grand Junction all pickup only. Thanks for looking. PM is the best way to reach me. Make offers, just want to clean up my life!
Last edited:
