Brett
Meat-Hippy
- Location
- Salt Lake City Utah
RedRock5.9 said:Correct. I think I still owe you, Cody or somebody else for nachos or drinks or something...
Lets just say that it was me.....now drive down the street and bring me some nacho's!
Brandon Gillon On Monster Garage
- Thread starter RedRockUT
- Start date
Lets just say that it was me.....now drive down the street and bring me some nacho's!
Ohms
'Poser Wheeler
- Location
- the gates of hell
James K said:
I'm thinking the same thing....Coil Overs,Links,Dynatrac 60's....
DOOD...I don't think so and I belive that I can prove it...Bu who knows, just my .02
Ya, I don't think you could build it for 20k. Just the axles would set you back close to 8-10G's. 40" krawlers on custom double beadlocks aren't cheap, Atlas 2g's, coilovers, 1500, motor/tranny, 1000, plus another 5000 in fuel stuff, shifters, linkages, tube, etc etc.
35000 is expensive, but I've seen similar comp rigs go for somewhere in that range. I'd rather have that bronco than a comp buggy I think.
Cody
35000 is expensive, but I've seen similar comp rigs go for somewhere in that range. I'd rather have that bronco than a comp buggy I think.
Cody
rockreligious
NoEcoNaziAmmo
- Location
- Ephraim
James K said:
dynatraks 8000 .... or .... 9"housing w/Hi9 thirds and 60 knucks 6000
coilovers 4000 .. or .... fox airshox w/winch FnR 1500
krawlers 1600 .. or .. barely used and from UROC comp 900
atlas 2000 .. or .. Atlas 2000
link stuff 1500 .. or .. link stuff 1500
fuel cell 200 .... .. fuel cell 200
fuel pluming 100 .. or .. fuel plumbing 100
tube 300 ... or .. tube 300
beadlocks 1000 .. or .. beadlocks (build own) 350
engine 300 .. or .. better engine 500
brackets 100 ... or . brackets 100
donor bronc 2000 . or . donor bronc 2000
________________________________________________________________-
22100 or with just as good but different parts 13650
Im sure I left some stuff out, cause theres always a couple of grand in stuff you dont even think about until your fabbing stuff up...but I think most of us wouldnt spend that kind of money on dynatraks unless your just wealthy or have it given to you and your fab show as advertisement. I could be wrong.
I figure its worth $35000 with $22000 in parts the labor and notoriety is worth the difference, just as I stated though I would only pay $15000 for it. I would only buy it if it was cheaper than I could build it myself cause part of the fun is building it yourself. If you dont enjoy the fab stuff but want a awesome machine and have the cash spend it, wheel it, and post pix so we can check em out.
Last edited:
rockreligious said:
well, you did say you could build it for $20K...not build something similar with totally different parts...if you can show me a set of hutchinsons ( four or five, I dont care) for $1000 then get me all you can cause they are a minimum of $500 a PIECE
rockreligious
NoEcoNaziAmmo
- Location
- Ephraim
Supergper said:well, you did say you could build it for $20K...not build something similar with totally different parts...if you can show me a set of hutchinsons ( four or five, I dont care) for $1000 then get me all you can cause they are a minimum of $500 a PIECE
I listed both there parts, and parts that I would rather use.
Its been a year since I seen the build so I couldnt remember what kind of beads they used, but even at that Id only be 4g's over budget with there same products. I believe they were supposed to have a build limit of $3500.
Id take the challenge if someone would throw me some FREEBIES.