Looking for a TH350/700r4/TH400 - NP208 adapter

[JIMBOB]

I just got a new TH350 for a YJ build I'm working on and I need to bolt my Dana 300 to it. I'm gonna try and save some cash by just using the 208 adapter with a Novak spud shaft. So if anyone has one kickin' around that they would be willling to sell or if you know someone that does let me know. I believe the stock adapters from a TH350/700r4/TH400 - NP208 will work.

It will look something like one of these. High foot or low foot doesn't matter to me.

 

[mbryson]

I may have one of those? Let me see what I have kicking around the garage. I think if I have one, it's for a 241. Is there a difference in the 208/241 adapter?

 

[DaveB]

I have some too, I have 700R4 to 208, TH400 to NP205, and possibly TH400 to 241. The TH400 bolt pattern is different than the th350/700r4.

 

[JIMBOB]

Oh is the TH400 different? From what I understand you actually have to elongate one of the holes on the t-case flange in order to get it to bolt up but I haven't come across anything like that for the tranny side. One article that I read through said that you could use any of the three (TH350/TH400/700r4) adapters to either the 208 or the 241. So mbryson, if you have one for a 241 it sounds like it should work. Then again I have no actual experience with the TH400 as I am currently running a 700r4 in another rig and getting ready to install this 350 so you may be right DaveB, the TH400 bolt pattern may be different. But it sounds like you have a 700r4 to 208 that would probably work.

 

[SWALLDOG]

The top pic you posted is for a th400 trans. Notice the 6 bolt holes where it bolts to the trans. The bottom pic w the two adapters are for th350/700r4 trans. Notice the 4 mounting bolt holes. Good luck w your search.

Probably @ work under a truck, Tapatalk 2

 

[mbryson]

Oh is the TH400 different? From what I understand you actually have to elongate one of the holes on the t-case flange in order to get it to bolt up but I haven't come across anything like that for the tranny side. One article that I read through said that you could use any of the three (TH350/TH400/700r4) adapters to either the 208 or the 241. So mbryson, if you have one for a 241 it sounds like it should work. Then again I have no actual experience with the TH400 as I am currently running a 700r4 in another rig and getting ready to install this 350 so you may be right DaveB, the TH400 bolt pattern may be different. But it sounds like you have a 700r4 to 208 that would probably work.

Mine is off of a 700. From what I know the TH350/700 share the same 4 bolt trans pattern. I really don't know about the T400 but would expect it to be different for some reason. I think SwallDog is right on with his assessment

 

[JIMBOB]

Ah I see what you mean. They are different. I didn't even notice that before. Thanks SWALLDOG. Like I said I've never really had any experience with the 400 other than just whatever bs I've read on other forums and such. They are clearly different though.

 

[B2-Bomber]

i have one from a 700r4 as well

 

[Diablo4130]

I have one off a th350. Located in Elko, NV id sell it for 50 bucks

 

[B2-Bomber]

mine is in kearns, and mine is free

 

[JIMBOB]

I can buy one online for less than $50

http://cobratransmission.com/index...._id=55016095&gclid=CPyFtpKZyrUCFe9aMgod7wEAHQ

 

[B2-Bomber]

i hope the one you got from me is what you needed

 

[JIMBOB]

Yep that's exactly what I was looking for. Thanks a lot and free no less. Let me know if I can do anything to pay you back. I work in a machine shop and do a lot of fab work so if you ever need some work done hit me up.