Anyone into 3D printing?

STAG · May 12, 2024

I’ve been running the Bulletpoint Mounting system in my vehicles for about a year and a half now for my phone mount.

They make an adapter for the JL/JT dash that replaces one of the dash hardware with a ball mount, but I don’t have a JT anymore so I wanted to transfer my mount over to the H2.

I mixed grey and black resin to try to color match the plastic of the H2 dash, and printed a ball mount that utilizes one of the factory dash bolts.

jeeper · May 12, 2024

STAG said:
Filament printed some caps/plugs for the intake manifold and the trans shaft outputs.
View attachment 172607

SxS or not, that engine won’t run with a cap on the intake.

Surprised you didn’t know that.

STAG · May 12, 2024

jeeper said:
SxS or not, that engine won’t run with a cap on the intake.

Surprised you didn’t know that

Ultimate air filter

STAG · May 13, 2024

Mock-up parts

glockman · May 14, 2024

I think I'm going to print some of these.

The_Lobbster · May 14, 2024

glockman said:
I think I'm going to print some of these.
View attachment 172678

I like it, but why not just do a couple chain twists to tighten it a tad?

anderson750 · May 14, 2024

glockman said:
I think I'm going to print some of these.
View attachment 172678

I would take a few of those

Herzog · May 14, 2024

glockman said:
I think I'm going to print some of these.
View attachment 172678

Good idea! That would be a good one to make out of TPE so if the chains needed to pull out it would just bend and open instead of snap. (I'm currently obsessed with TPE)

glockman · May 14, 2024

The_Lobbster said:
I like it, but why not just do a couple chain twists to tighten it a tad?

I hate twisted chains. My OCD thinks they look bad and my shade tree engineer thinks they can't be as strong when twisted up. Not backed by any science, just my feels.

Herzog · May 14, 2024

Just another stupid dust cover but I'm obsessed with this stuff

Making some for my air lines in the buggy and taco

I can drop .stl files if anybody wants them just let me know, but be warned these are for JACO high flow couplers so they are a tad larger than normal.

jeeper · May 14, 2024

glockman said:
I think I'm going to print some of these.
View attachment 172678

Obviously, you and I get the same Instagram ads.

SoopaHick · May 15, 2024

The_Lobbster said:
I like it, but why not just do a couple chain twists to tighten it a tad?

Any rigging course will tell you twisted chains will kill you and send you straight to the lava pits of doom. But in reality twists in a chain lessens the strength drastically.

The_Lobbster · May 15, 2024

Can we get some of these mini balls printed? This one looks like it’s just an old 1/4” rod end, but something printed would be great.

STAG · May 18, 2024

Let’s see if the ol’ FDM printer can make it through no issues! If it does, this is 1 of 4 similar parts to be made, so 20+ days of printing.

I Lean · May 18, 2024

STAG said:
Let’s see if the ol’ FDM printer can make it through no issues! If it does, this is 1 of 4 similar parts to be made, so 20+ days of printing.

View attachment 172798

You'll need to stop it to swap filament?

STAG · May 18, 2024

I Lean said:
You'll need to stop it to swap filament?

It just stops where it’s at when the runout sensor trips, then toss on a new roll and hit resume. Works very well

STAG · May 18, 2024

I Lean said:
You'll need to stop it to swap filament?

Also can get big rolls

I’ve done both.

STAG · May 23, 2024

STAG said:
Let’s see if the ol’ FDM printer can make it through no issues! If it does, this is 1 of 4 similar parts to be made, so 20+ days of printing.

View attachment 172798

Finished earlier than estimated, and used a little less filament than estimated. (Maybe used 1900g)

glockman · May 24, 2024

STAG said:
Finished earlier than estimated, and used a little less filament than estimated. (Maybe used 1900g)

View attachment 172965

And the finished product is?

STAG · May 24, 2024

glockman said:
And the finished product is?

V1.0 of portal boxes. I’m not going to print the others yet because printing this one has given me a few parameters I already want to change for the next version.

Orienting it was the only way I could get it to fit in the build volume. Used almost all of the 450mm z height.

I’ve already redesigned it to be smaller and better looking 😂

Anyone into 3D printing?

Well-Known Member

I live my life 1 dumpster at a time

Well-Known Member

Well-Known Member

I hate Jeep trucks

Well-Known Member

I'm working on it Rose

somewhat damaged

I hate Jeep trucks

somewhat damaged

I live my life 1 dumpster at a time

Certified Weld Judger

Well-Known Member

Well-Known Member

Mbryson's hairdresser

Well-Known Member

Well-Known Member

Well-Known Member

I hate Jeep trucks

Well-Known Member