General Tech What did you work on Today?

YROC FAB.

BUGGY TIME
Vendor
Location
Richfield, UT.
Not sure I follow? This is the back of the heat exchanger.
kGYpqfB.jpg
Thats exactly what i meant. Forced air heat exchange for the win. I did see a fan in your original pics.
 

zmotorsports

Hardcore Gearhead
Vendor
Location
West Haven, UT
Last night I thought I was going to have to clear snow when I arrived home from work but seeing as how that wasn’t the case I opted to rack the Jeep and do a LOF service as well as finish up the press work table.

Oh, and for the record I absolutely HATE the looks of mud guards on my Jeep but I'm trying to be somewhat legal.

6a87a6085ed254242a94b146da7b9be9.jpg


I tried out my new connector pliers and they sure work slick.
1a12889da99ed6da3a8e60a7a5174920.jpg


These 37’s sure seem bigger when they’re off the Jeep.
ec0aa576f9a6fe17e2360c9a63d665f4.jpg


e09658c1adb2a808dbc549a59e53460f.jpg


They are wearing excellent so far. New they had 18/32” and they are still at nearly 14/32” with just over 15.5k miles on it in exactly a year now.
65ebd66fe916259cfd5fc8e23e0041a6.jpg


622b0fec8fe20db582cdd41385e2ce6d.jpg


The LS engine is actually easier to change the oil than the OEM 3.8 liter Chrysler engine. The oil drains without running all over my suspension links and the filter drops straight down at the rear of the engine vs. the front near the harmonic balancer which would have oil running down my steering drag link and tire rod.
5bca5c1ae104dc5e88d4a312d220f6b9.jpg


While the oil was draining I welded the gussets on each channel for my press work table.
8d78a275cb13fe17e69f8c540817956b.jpg


2d14d351abb5b6234784018e402b66bf.jpg


978060e6b5ad14fe4473b2ce6a867379.jpg


36d9cb0e0c5e2cd8fb0cb4fd40c02c31.jpg


08d9436d894271503430079c553da67f.jpg


Also, while I had the welder out I went ahead and repaired my welder’s third hand again and hopefully for the last time. I used a Cummins N14 wrist pin as the weight when I built this one and butted the 5/16” cold rolled stock up against the end and TIG welded it but several times now it has broken off right at the HAZ. This time I extended the round stock under the wrist pin which should hold much better and not be so delicate.
678416a437abfb5edd9a7961183c0b27.jpg


I then added some silicone bronze to the tip similar to the feet which promotes good current flow when using as a ground.
fcad9266f0d4fd1ac1186fd46583b69a.jpg


936b464e209fa921089d3f11cd5c1d88.jpg


I painted the work table so it could be drying while I finished up the service on the Jeep.
405d34d34088d671477fb20ae6df2aec.jpg


Some good ole’ Chevrolet Orange should hell it perform better.
c7bda85aa0aac01fb278c8c7d77570c2.jpg


Installed with the lift cables adjusted.
e4d547d4d2ef7656f156fd35a41f064f.jpg


Completed with arbor plates residing on the table.
fe0537ff89886fac58da6aaff397fd4c.jpg


Lastly, after test driving the Jeep and parking it in the garage I swept up and took one last picture before locking up for the night.
8a08a73052cba9f4edfc468e90b2763a.jpg


Thanks for looking.

Mike
 

2002maniac

Active Member
Location
Brigham City
You can't give us that little tid bit of info and leave us hangin! What are the details on this? Can't say I've ever heard of an explorer caliper upgrade/

Buddy of mine runs an XJ in the BITD Jeepspeed class. He's been going through a set of front pads every race because of flex in the wimpy single piston calipers. We decided to go with 2 piston explorer calipers but stuck with the stock rotors so he could keep his 15" wheels. I think most xj brake upgrades require larger wheels.

I trimmed excess bracketry from the knuckle and used 2 of the hub mounting bolts to secure the bracket. The bosses on the knuckle were milled down to allow us to use the stock length hub bolts.

Here's the 3d printed prototype bracket:

20200107_180604.jpg
 

Hickey

Burn-barrel enthusiast
Supporting Member
My OCD thanks you (mostly)
I'm still not totally happy with the setup. I really wish I would have bought the other style Speedbumps for the rear. I'll likely change them out one day, the same day that I cut off the lower coil mounts and weld new ones back in at the correct position so my pinion angle is correct.
 

zmotorsports

Hardcore Gearhead
Vendor
Location
West Haven, UT
My son and I made a little progress on the front bumper of his WJ over the last two nights.

After scratching our heads a bit we devised a pretty slick mount that will be both functional and strong. Being a unibody we need to ensure the fasteners won’t pull through the sheet metal as well as spread the load out all while keeping it as tight up to the core support and grille as possible yet not obstruct airflow through the radiator.

After some measurements we started cutting some 1/4” plate.
289ddf1f285ab0ad599245a335c981c8.jpg


Once one side is mocked up I disassembled and used transfer punches to duplicate.
2dc777216acb5990fefa80e5a9b43b89.jpg


Test fitting with 1/2” bolts.
282fae65624ff40e9264fedbecfed319.jpg


1596c0bc1dd4d02f49a863960da84766.jpg


All four pieces cut, trimmed and test fit before prepping to weld the nuts in place.
c4c75a02fb4f942c4d0f5026ce49260a.jpg


9646c7221cdf008c5422646837c6989f.jpg


I generally use muriatic acid to remove the zinc coating on the nuts prior to welding but i opted to just knock the coating off the flats with the belt sander tonight which is why the soot.
34a4eee37cec815bdeb1387b8c920276.jpg


e18f75e900c9879774deb1c9885b6651.jpg


Bolted in place.
a6240efba15712a941f9409d201ce02d.jpg


64a65c6313d1440c357e0024751e9c92.jpg


e03128074e4db560f950e5b77d15ae9e.jpg


Here is where it could be a bit “Fleet” and not rigid enough when using the winch in a recovery situation so I opted to add some strength by creating a rib or backbone to the mounts.
b1e628783a183c7fbdb0619be4d089a0.jpg


2e6cc612975ba1e68fed83210e597c67.jpg


c354ffdc18fd23a48a877cb389ff056a.jpg


10ccd66e7f2c4906e0497474a487e4f6.jpg


Thanks for looking.

Mike
 

jeeper

I live my life 1 dumpster at a time
Location
So Jo, Ut
I thought only people in west valley parked on their lawn :D

so did my neighbors that were moving in while we were knocking down the wall!! Guess they picked the wrong neighborhood!

Rest assured, we are not actually parking on the grass.

Just driving on it:rofl:

The trailers can be backed all the way around the back of the house to their proper location. This just allows me to move them each one at a time in any order. Previously, I would be 3 or 4 trailers deep sometimes and have to move the first 3 to get to the 4th.
 

Hickey

Burn-barrel enthusiast
Supporting Member
so did my neighbors that were moving in while we were knocking down the wall!! Guess they picked the wrong neighborhood!

Rest assured, we are not actually parking on the grass.

Just driving on it:rofl:

The trailers can be backed all the way around the back of the house to their proper location. This just allows me to move them each one at a time in any order. Previously, I would be 3 or 4 trailers deep sometimes and have to move the first 3 to get to the 4th.
Every day you're shufflin.
 

Hickey

Burn-barrel enthusiast
Supporting Member
Today I finished up several projects to prepare for a trip to Texas in a couple weeks.

Wired up a replacement for my 3rd brake light that fills two holes left in the tailgate after removing the spare tire.

95675B25-299F-400B-8F84-4406F0E845E8.jpeg

Finished building a platform to go on top of my spare tire.

213D2CDE-3D53-497D-BFF6-187964854020.jpeg

And removed the back seat and built a platform for two loving adults to sleep on. This is actually wider than the mattress in my work truck by several inches.

987AE44C-7E03-4A8F-9B29-769139950827.jpeg
 
Top