Search results

  1. Milner

    Custom axle housing work in the SLC area ?s

    Thats actually pretty cheap! Charles has been do this for 20+ years!!!! We charged more than that 10 years ago when I worked at AFWDS and Charles was doing the work there! You want it done right, pay the man, you won't regret it!
  2. Milner

    4 1/2" grinders, best bang for the buck

    Pretty sure the sears/craftsman are also made by dewalt/black&decker....
  3. Milner

    4 1/2" grinders, best bang for the buck

    They have lock-on buttons at the base of the paddle.
  4. Milner

    4 1/2" grinders, best bang for the buck

    Yep, lots o abuse....oh, and I dropped it after it attacked me!!
  5. Milner

    4 1/2" grinders, best bang for the buck

    Between B and I, we have 1 dewalt an 3 BlackDecker HD's. They are the same grinder,different color, repair parts are the same. Replaced r/p in the dewalt and cords on ouple of the BD's. I would stay with one of them!!!! The new Home Depot ones have a good waranty though.
  6. Milner

    re-packing your R+P :)

    Parker had a frt 60 with packed bearings....Saved the housing/bearing, too bad it did'nt lube the r/p.... Old guy at Boyce packs all the bearings when he rebuilds them....
  7. Milner

    Dana 30 locker opinions please

    Never tried the locker, but I DON'T like the gears!! Never set up very well, finish is not as good.....
  8. Milner

    Off-Road Engineering in No. SLC

    Ash???? What happened to Anitol??
  9. Milner

    What Do You Guys Think About This Early Bronco?

    Depending on the body, maybe a little high. The lift is pretty worthless unless it is a newer style. Most the older lifts are harsh stiff springs. Is it an auto? if it is truly a 76 it should have disk frt and powersteering. The steering should be the inverted Y style, really should change to...
  10. Milner

    Off-Road Engineering in No. SLC

    Hey Kurt???? I bet D would have an entertain response???? :rofl: Anyway, I would go there, but........ :D
  11. Milner

    electric vs hydraulic winches

    Hydro is SLOW!!!!!! Only advantage to hydro is if you use it DAILY, service duty life is greater, built for constant use. Electric is faster, easier, more simple to install. Better for occasional vehicle recovery. JMHO
  12. Milner

    stolen towrig/buggy Skinny'sin AZ

    check this out!! http://www.pirate4x4.com/forum/showthread.php?s=&threadid=213433
  13. Milner

    Dana 60 vs Toyota P/U Axle Shafts

    Then compare frt to frt..... frt 60 1.5" 35 splines That rear 60 is 1 5/16" 30 spline, same as 44.
  14. Milner

    Cool Fab Work

    Check out the skunkworks at www.race-dezert.com Some very cool fab work there too!
  15. Milner

    UROC Sites

    Hope not.....
  16. Milner

    let's talk about 4-links

  17. Milner

    let's talk about 4-links

    Never ran the #'s but B's is over 100%, guessing, I'd say 150%. The links have a steep angle. Another note: remember that if the uppers are shorter than the lowers, the pinion tilts towards the ground as the suspension droops. So be carefull, if you shorten the uppers to get AS where you...
  18. Milner

    fuel injection question?

    Pump working? (Hard wire the pump to the ign, be sure to have a return line)Holley varies the ground to control the pump...SUCKS. Use a toothbrush with some carb cleaner and clean the head of the injectors. The injectors can be removed and cleaned....Basically the same thing as a Chev tbi...
  19. Milner

    let's talk about 4-links

Top