Search results

Still got this?

Sorry about your bias to 14B's but in all reality for packaging, aftermarket, information, strength and availability they cant be beat. The way @YROC FAB. and i built mine its got a super smooth and tough belly now. - I agree with the knuckle/hub combo. 05+ are easily available, researched, and...

I'll trade ya drowned goldfish and a hairless ferret ready for fur harvesting.

Got bored today and decided to check out what’s been rattling on my duramax. It’s an inconsistent rattle, does it idling, running down the road, hit a hole and it does it etc. it’s not rhythmic or mechanical sounding just a random pinging noise. Ended up finding it, was a tranny line hitting the...

Little more done on the front plate of the rear truss. Took a few tries before I finally settled for one I liked, roughly 7. Will look tough once it’s all done 🤘 First a rough cut with constructive criticism memos Adding card board to fill gaps Fine tuning And a stack from the first...

No problem, that’s what these places are for 🤘

Yeah, this one is off a 2011 Silverado. All 4thgen truck motors have this style but it’s commonly referred to as the TBSS intake. Got it all prettied up and all the unnecessary stuff plugged and fixed up for how I’m gonna need it then of course I had to make sure the heathens of the shop knew it...

Finally took some time to do some much needed maintenance on my lady’s fiat. Changed the oil, cleaned the air filter, rotated tires, checked brakes, all that jazz. But the high light of it all was I got bored and realized there were no tow points on the front lol so I made these. 1/4” plate with...

Scored this little thing today, and on this note, I have officially decided that I’m going to be rebuilding the motor and throwing some goodies in it as well 😈 I’ll be digging into it after I get my axles out of the shop 🤘

Next I’ve been fiddling with the ram mounts and truss ideas and we finally came to these. Got the ram up in place but realized off the bat it needed to move in and down other wise it was gonna stick way the hell out! So to conquer that I cut the cover open and recessed in a piece of tube...

Little update, been plugging away on the rear diff some more! Random pieces, made little grease fittings for the wheel bearings and removed the axle shaft bearing to make room for the future stub shafts

Don’t worry gents I’m currently training an an alcoholic rabid raccoon to bite nuts that we will leave for him in his work truck next time we see him

Here’s the one I plan on running. Had an aluminum one that claimed to be 12.5k rated but noticed it had cracks around the pin holes for the ball part of it after a few uses so I sent it back. XPE Trailer Hitch Fits 2.5 Inch Receiver, 8 Inch Adjustable Drop Hitch, 28,000 LBS GTW- Tow Hitch for...

I’d be tempted to throw my grand cheapokee in if it’s allowed being that I purchased it for $1200

Almost forgot to show these beauties off. Cory laid down some amazing welds as per norm, even with the material being thin and on edge, helping me bring this nonsense to life. The airfilter housing all buttoned up and filter fits perfectly in it with plenty of squish going on to keep it sealed...

Knocked out my steering cooler, 2.5”OD x 25”L x 1.5”ID 6061 aluminum. Fins are .100 thick with .125 gaps, took out 5/16” of material leaving a 3/16 wall. Also made sure to hit the edges with a nice triangle file and then built some end caps with some -10jic ends. And yes it took some time and...

Next we got some aluminum work going on. Got my trans cooler fan shroud made. Just need to tack my spider on and send it to powder. Next was my air filter housing. Using a Wix 10304 paper filter that’s meant for 14-18 ram promaster vans and random pieces of equipment. Housing will be 7.5”...

So sadly y’all do to some life changes I’m gonna back burner this for awhile, probably till next winter due to job change and an upcoming army vacation. I will be knocking out a bunch of little things on it though that can still be done without a chassis so here goes all that nonsense. First up...

JM Rigging out of Cedar is your go to for quality. 3/8"x85-90ft is all you're gonna be able to fit.