B.a.m.f.

[notajeep]

I LIKE!!!!!!

 

[tc meiser]

update.....

ok i got a little more done on the roll cage last night. as much as i could until we ran outta tube. By the way... dose anybody have some that i can buy? I need 1.75 .120 Wall. Let me know thanks. Here are the pics

 

[tc meiser]

Gotta couple pics of the front fenders finished up and the flat belly.

 

[tc meiser]

Here is what we have left to do:
-Finish the steering as in just the shaft to the wheel.
- Finish plumbing rear breaks
- Mount seats and belts
- Finish cage with some braces
- make two peice front drive line
- put all the wiring in looms now that the wiring is done

We have got to have all this done by the first week of Ocotober. We are goning to Moab. So if any of you want to plan on going down with us just let me know.

this is the jeep at ride highth next to my dad that is 5'10 so its an inch or two higher then i planed but still pretty low for a full body jeep. on 42's

 

[tc meiser]

Here is a few pics of when we first rolled it outta the garage when the suspensoin was done. Woo WOo

 

[genheath]

New Ride - BAMF

Hey, TC...fab work and welding....EXEMPLARY!

Finally was able to see your build pics. Impressive!! Here's a thought...I've wheeled with you a few times and I know your affiniety for deep water. Your new ride isn't high enough. Better add another 12" to those tires and 6 more inches to the body lift....unless you have designed and amphibious ride here. I think it's appropriate that you have "BOAT" rockers.

Courtney

 

[Corban_White]

How well does that engine-hoist cylinder work for bending? I thought they needed to be more or less upright to work properly, but here you are using one. Work OK?

I have the same setup. It works great. The air pump needs to be on the bottom to work. Check out http://www.offroadfabnet.com/forums/showthread.php?t=303 for more info.

 

[tc meiser]

update.....

alright i got the shocks on last night with the hoops and a few ohter pics...

 

[tc meiser]

couple shats of it out of the garage sits a little low in the rrar all because thr rear coils are not it yet so the will be on tonight allong with the rest of the cage i will update you later on that... i have a few pics of the joints on part of the cage there pretty cool looking

 

[tc meiser]

update.....

i snap a few pics of one of the battery tray we are going to have dual baterys on the jeep

 

[tc meiser]

i also got a couple of the sterring mount and the shaft the way i ran it i took the shaft and cut grove in it then slid it through the sleeve and drilled a hole tap it and put a grease insert in it

 

[tc meiser]

i got alot of the cage done and the seats mounted ,the guys at teraflex helped us out we went and bought some seats and wheel spacers from them thaks agin.... ill post up those pice latter

 

[OREGON85]

Wow, that looks REALLY good!

 

[tc meiser]

update.....

i got a little further on the cage. put in the windsheild tubes and a couple door bars. i also got a tube behind the seat to mount the seatbelts to. We also installed a few rock lights here are some pics for you guys.

 

[Bart]

Nice looking cage.

 

[tc meiser]

update...

sorry guys for such a late update. just been busy getting this jeep done. We are leaving for Moab October 17th. the first trip out. the jeep currently is 95% done. Its been a long 5 months that we have been working on it. I've got the seats installed, got the complete floor in. Seat belts installed. here are a few pic:

 

[tc meiser]

got the steering bracket done, finished up wheel wells, front winch sucked down, hood pins in, built custom gas pedal assembaly with some bitchin petals. installed two lights Hella 500ff there is going to be two more in the original jeep grill holes. Here are a couple pics.

 

[tc meiser]

The jeep can drive now we are down to a few more things and it is ready to go here is a few poser pics

 

[jsudar]

Those pedals are killer. Did you use a baby dimple die on the holes?

One other question: when you welded you axle center sections to the tubes, what rod did you use?

 

[Bart]

Looking way cool TC. What did you use for your floor? Looks like steel.