Search results

One of the guys that I work w/ only gets a ticket about 10% of the times that he is pulled over. One time he was pulled over going to Vernal going OVER 100 MPH through those twisty canyons on Hwy 40. :ugh: The local Sheriff let him go if he promised to slow down. Well he was pulled over again...

Napa has it for $69 after mail in rebate right now. -Brad J

Yes if you get the bellhousing from a SII w/ a AMC 6 to TF727 tranny. You just need to change or move the motor mounts from what I've heard. Lazarus401 should know. You could also check on the BinderBulletin. -Brad J

I have heard about a hole in the ground that is actually called "Blow Hole" close to nutty putty. I've been in Nutty Putty a dozen times but have not found the other cave. Which direction is it from Nutty Putty entrance? and is it a rapel only cave? I hope they don't close down the cave. People...

Maybe that's my problem, I used the original proportioning valve. I've heard to ditch it and run the Wilwood Proportioning valve to the rear to let the front brakes do most of the work. Do you think I would be ok w/ the stock proportioning valve but w/ the new vette MC? I've been worikng on it...

Checker had Herculiner for $80 last week on sale. Sam's club has had Herculiner in the past 1 gallon plus an extra quart for $80 or $90 if I remember correctly. I used the $45/gallon Duplicolor on a project for the kids to see how it works. :ugh: - Brad J.

Right now I regret Disk braking the D60 on my Scout because the e-brake doesn't hold and its nearly imposible to take up the tension on the e-brake cable. I used an IH D60 so the bracket I ordered from Great Lakes Offroad ($75) needed to be reworked to fit. I used 78 Caddy Calipers ordered from...

We used to go camping there every summer when I was in HS. Its located in Skull Valley the next valley West of Tooele and Grantsville. Its north of Iosepa, take I-80 to xt 77 then go south 5-10 miles. There are tons of trails on the east side of the road that run through the camp grounds and up...

I'm still using an old 14" CRT monitor so 800x600:sick:. My plan down the road is to run dual LCD's w/ one switched to the KVM to switch between computer's. -Brad J.

Very sorry to hear about that Chuck, hope your family is doing OK. :( -Brad J.

Ouch ! :( :( Hope your doing better now. -Brad J.

I found a really clean 392 in the junkyard just east of Roosevelt before the painted overpass, Its a long drive for one unless you have a reason to be out there. There is also a travelall w/ a 4 barrel intake at A1 auto on 2100 South freeway close to Rocky Mountain Raceway (not positive that its...

Which motor do you have in it now? I have a 304 in my 800A and picked up a 392 for $200. My 304 runs so good that I'm not in a big hurry to swap it out since I don't know the history on the 392. I've seen afew 392's around also. Good Luck, Brad J

Sherwin Williams is just to the North of Auto Zone on Hwy 89 about 600 South in Bountiful. I don't know if they carry what your after though. Good Luck, Brad J.

Our office used to be up by the Cotton Bottom and I had always heard the old timers talk about the place (wives hated the place). It wasn't what I expected w/ a name like that. They were famous for their Garlic Burger w/ my office, it actually tasted pretty good. -Brad J.

It almost happened to me right there also, I went too far to the right felt like I was going to roll over so kept going to the right and drove over the edge and landed on my tires. Scared us all pretty good. :eek2: -Brad J

Nice Place but spent over $100 there, wife wanted King Crab ($47) :eek2: Wish I could offer some more ideas, Village Inn is fancy for us. I hate being poor. Good Luck, Brad J.

I'm getting closer to getting my scout on the road & in for inspection & now need mud flaps. I was at NAPA in Evanston today and they had 2 different kinds (Ford Lover or Flames) and I didn't like either of them. I will be running 35's or bald 37's and would be happy w/ plain black semi ones cut...

Nice, Did you buy it from someone in North Salt Lake because it looks exactly like one up here. That is a lot of lift on it. I'm jealous. Good Luck with it -Brad J

Thanks guys, I was off on the years, I think I need to get another set of 76-78 calipers. I think mine are not going to work for some reason. Thanks, Brad J.